TM OWNER INSTALLATION AND USER MANUAL Series 3000 Models 3214, 3314, 3316 & 3414 Automatic Garage Door Opener F
10 Step 11: Install Wireless Infrared Safety Sensors Wall Mounting Bracket (If Included) Select a mounting position 5 inches above the floor to cen
11 Step 14: Install Wired Infrared Safety Sensor Wall Mounting Brackets Use the following instructions if your opener is equipped with Wired Infra
12 Step 16: Install Wiring for Wired Infrared Safety Sensor Identify which side of the garage door opening (if any) the sun is “likely” to shine o
13 Step 18: Mount Wired Infrared Safety Sensors Attach the sending and receiv-ing units to the “U” brackets by inserting their tabs into their resp
14 Step 20: Wireless Wall Station Security Code Change and Programming Note: The following steps describe the process to change the Wireless Wall St
15 Step 21: Alignment of the Wireless Infrared Safety Sensors Use the following instructions if your opener is equipped with Wireless Infrared Safety
16 Step 22: Alignment of the Wired Infrared Safety Sensors Use the following instructions if your opener is equipped with Wired Infrared Safety Senso
17 Programming Transmitter to Power Head Unit Note: Do not press any button on the Transmitter until instructed 1. Press the PROGRAM Switch button
18 Step 24: Connecting Door Arm to Trolley Trolley must be at the factory preset fully close position. If not, activate opener to bring trolley to f
19 Step 27: Setting Door Close Travel Plus “Contact Obstruction Sensing” Test With wall control up/down button, activate door to full open position;
2 Read These Important Safety Rules Before Proceeding IMPORTANT INSTALLATION INSTRUCTIONS WARNING: To reduce the risk of severe injury or death: READ
20 NOTE: Confirm that the door has stopped in the UP position as a result of the Upper Limit Switch and not because the Trolley has hit the open Stop
21 Step 31: Installing Wireless Keyless Entry (If Included) Install all wall controls out of the reach of children and in a location where the door
22 OPENING FORCE ADJUSTMENT To determine that the opening force is not excessive, grasp the door handle or bottom edge during upward travel. If the o
23 IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of severe injury or death: Before you proceed, please thoroughly read the safety rules on
24 HOW TO ACTIVATE THE OPENER Never let children operate or play with door controls. Keep remote control away from children. Use any of the follo
25 HOW TO OPERATE THE WIRELESS WALL STATION (If Included) Never let children operate or play with door controls. Keep remote control away from childr
26 HOW TO OPERATE THE DOOR MANUALLY – Emergency Release Disconnect The door should be fully closed if possible, weak or broken springs could allow an
27 MAINTENANCE OF YOUR OPENER SYSTEM Test door opener monthly. The garage door MUST reverse on contact with a 1 inch high solid test ob-ject on the f
28 TROUBLE SHOOTING SECTION SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Opener won’t work from wall button or radio control. No power to opener. Sho
29 Parts Breakdown Rail Assembly – All Models #. Part # Description # Per Unit #. Part # Description # Per Unit 1a. 28
3 Veuillez lire ces règles de sécurité importantes avant de commencer les travaux IMPORTANT —NOTICE D’INSTALLATION— AVERTISSEMENT –POUR REDUIRE LES
30 Parts Breakdown Power Head Assembly And Accessories – All Models #. Part # Description Per Unit #. Part # Description
31 QUANTUM ACCESSORIES Three Button mini/visor Transmitter Part# 302083 Controls up to 6 doors or wireless ac-cessories. Includes visor clip. Wir
32 Questions? For quick answers and helpful advice, Call Toll Free 1-888-827-3667 Cut Template to Aid in Keyless Entry Installation (See
4 Automatic Garage Door Opener – For Residential Doors Only FEATURES 1. Open and Close Cycle Control: Allows garage door to be started and stopped
5 IMPORTANT PRE-ASSEMBLY CHECK If assembling a motor head unit from a factory sealed box skip this check. Every Power Head Unit is factory tested and
6 Step 1: Attaching Motor Power Head Unit to Rail Before assembly, align sprocket/coupling cogs to match notches of driver gear. Rotate the Motor Sp
7 Step 3: Attach Unit to Front Wall Bracket Raise the front end of the opener and attach it to the front wall bracket, using the ¼” x 4” hex head bol
8 Step 6: Mounting Door Bracket Fiberglass, aluminum and steel doors must be reinforced to prevent damage to the door. Check with your garage door ma
9 Step 9: Installing Deluxe Wireless Wall Station (if included) Install all wall controls out of the reach of children and in a location where the do
Comments to this Manuals