Wayne-Dalton LIGHT COMMERCIAL DOOR 6100 Owner's Manual

Wayne-Dalton highly recommends that you read and fully understand the Installation Instructions and Owner’s Manual before you attempt this installatio

Vertical Tracks Tools Required: Power Drill, 3/16” Drill bit, 7/16” Socket driver, Tape measure, Level, Step ladder, Safety glasses, Leather gloves 1

IF YOU HAVE TOP FIXTURE ASSEMBLIES:Align the top fixture base 3” down from the top section or below strut and even with the edge of the top section. Th

WARNINGWARNINGDO NOT RAISE DOOR UNTIL HORIZONTAL TRACKS ARE SECURED AT REAR, AS OUTLINED IN STEP, REAR BACK HANGS, OR DOOR COULD FALL FROM OVERHEAD PO

(2) 3/8”-16Hex nuts(2) 3/8”-16 x 3/4”Truss head boltsLeft end bracketUpper slotLower slotsHorizontal track angle(3) 5/16” x 1-5/8” Lag screwsCenter Br

Torsion shaftCenter bearingRight hand wound, red winding cone (left hand side)Left hand wound, black winding cone (right hand side)Right hand cable dr

NOTE: Ensure both torsion keyed shafts have equal amounts of the shafts extending from each end bearing bracket.Typical center bracket bushingStationa

WARNINGWARNINGFAILURE TO ENSURE DOOR IS IN A CLOSED POSITION AND TO PLACE VICE CLAMP ONTO VERTICAL TRACK CAN ALLOW DOOR TO RAISE AND CAUSE SEVERE OR F

WARNINGWARNINGKEEP HORIZONTAL TRACKS PARALLEL AND WITHIN 3/4” TO 7/8” MAXI-MUM OF DOOR EDGE, OTHERWISE DOOR COULD FALL, RESULTING IN SEVERE OR FATAL I

Door Arm HookupAlign hole in the door arm with holes in operator bracket tabs, as shown. Attach with 5/16” x 1-3/4” cotter pin and cotter ring, as sho

Cleaning Your Garage DoorIMPORTANT: DO NOT USE A PRESSURE WASHER ON YOUR GARAGE DOOR!While factory-applied finishes on garage doors are durable, it is

Important Safety InstructionsDEFINITION OF KEY WORDS USED IN THIS MANUAL:WARNINGWARNINGINDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH; IF NOT AVOID

WARNINGWARNINGGARAGE DOOR SPRINGS, COUNTERBALANCE LIFT CABLES, BRACK-ETS, AND OTHER HARDWARE ATTACHED TO THE SPRINGS ARE UNDER EXTREME TENSION, AND IF

Limited Lifetime warrantyModel 6600Wayne Dalton, a division of Overhead Door Corporation (“Seller”) warrants to the original purchaser of the Model 66

Please Do Not Return This Product To The Store. Please call 1-866-569-3799 (Press Option 1) and follow the prompts to contact the appropriate customer

Pull down rope(if included) Inside lift handlesCable drums RH/LHTorsionsprings RH/LHCenter bracket (as required)Center bracketbushing (as required)Lif

NOTE: If nailing product at 40°F or below, pre-drilling is required.NOTE: Allow the weatherstrips to return to room temperature prior to nailing to ja

5A. FLAG ANGLES (AS REQUIRED):A1. Quick Install (Q.I.) Flag AnglesA2. Fully Adjustable (F.A.) Flag AnglesB. JAMB BRACKETS (AS REQUIRED):B1. Quick Inst

INSTALLATIONBefore installing your door, be certain that you have read and followed all of the instruc-tions covered in the pre-installation section o

between the bottom jamb bracket and flag angle of the 2nd hole set. Secure jamb bracket using (1) 1/4” - 20 x 9/16” track bolt and (1) 1/4” - 20 flange

#1 Center hinge(s)#1 Graduated end hingesLong stem track rollerLower hinge leafs#2 Graduated end hinges (roller inserted into tubes furthest from sect

Lift handlesBottom sectionTypical placement of pull handle referenced on single wide doorsLock sectionTypical placement of pull handles referenced on