Wayne-Dalton Optimal Owner's Manual download pdf (Page 35)

�

Up-Down Button:

Momentarily pressing the Up/Down Button activates the door. If an

out-of-balance condition causes the door to stop while opening or

reverses the door while closing, apply constant pressure to the

Up/Down Button until the door is fully open or closed. This will allow

the Opener to move the door in an out of balance condition, until the

problem is corrected (see Troubleshooting). The Up/Down Button

(when unit is closed) can be activated by pressing flip cover.

THE SEVERE OUT-OF-BALANCE CONDITION MUST BE CORRECTED

IMMEDIATELY. FAILURE TO MAKE ADJUSTMENTS/REPAIRS, COULD

RESULT IN SEVERE OR FATAL INJURY.

Light Button:

Momentarily pressing the Light Button turns on the Light Fixture. The

Light Fixture will remain on until either the Light Button is pressed

again or the door is activated. The Light Fixture automatically turns on

with a door activation and remains on for five minutes. Pressing the

Light Fixture Button before the five minutes has elapsed will turn off the

light fixture. While the door is in motion, the Light Button functions

identically as the Up/Down Button, stopping or reversing the door

immediately.

Timer Button:

Momentarily pressing the Timer Button causes a delayed activation of a

stationary fully open door. The Opener will signal seven beeps (approx.

8 seconds) then beep constantly for two seconds prior to closing the

door, allowing time to exit the garage when the Opener is in the timer

mode. Pressing any button, except for the Profile Button while the

Opener is beeping cancels the timer mode.

NOTE: The Timer feature will only function with the door in the

full open position. Pressing the Timer Button with a stationary

door in any other position will cause the Opener to beep four

times and the door will not be activated.

While the door is in motion, the Timer Button functions identically as

the Up/Down Button, stopping or reversing the door immediately.

Slide Switch:

The Slide Switch has two positions: Normal, and Door lock.

Normal position:

Move the Slide Switch to Normal position for all normal functions of the

Opener. The Normal position will cancel the Door Lock feature.

NOTE: When the Slide Switch is moved to the unlocked

position the Opener will beep once.

Door Lock position:

If the door is stopped (fully open, fully closed or partially open) move

the Slide Switch to the Door Lock position to suspend all normal

functions of the Opener. The Opener will remain completely disabled

and non-operational in this mode. All Wall Stations, Transmitters and

Keyless Entry Units are ignored until the Slide Switch is moved to the

Normal position. If the door is moving when the Slide Switch is moved

to the Door Lock position, the Door Lock mode is not activated and all

functions of the Opener remain active.

NOTE: When the Slide Switch is moved to the locked position

the Opener will beep twice.

Operating the Wireless Wall Station

Backlit LED Lights:

The Up/Down arrows’ backlit red LED blink intermittently to help you

locate the Wall Station in a dark garage. This blink rate can be

changed for longer battery life or can be turned off. The default blink

rate is one blink per second. For longer battery life the blink rate can

be changed to blink once every two seconds. To change the blink

rate, remove the battery cover and remove one battery. Re-install the

battery and within 2 seconds, press the Light button. Re-install the

battery cover.

For longest battery life, the blink can be turned off. To turn off the

blink, remove the battery cover and remove one battery.

Re-install the battery and within 2 seconds, press the Pet button.

Re-install the battery cover.

NOTE: The Wall Station’s arrow LED will light while any Wall

Station button remains pressed.

Pet Position:

Pressing the Pet Button opens a closed door to a preset position

between eight and thirty inches above the floor, allowing pets to enter

and exit the garage without the door being fully open. The door must

be fully closed to activate the pet open feature. Pressing the Pet

Button with a stationary door in the pet open position will cause the

door to close. Pressing the Up/Down Button while the door is in the

pet position will cause the door to open. While the door is in motion,

the pet button functions identically to the Up/Down Button, stopping

or reversing the door immediately. The pet feature allows for custom

setting of the pet position door height. See Customizing the Settings

on page 31.

NOTE: A door in the “pet position” (open 8-30 inches) is not locked

and should not be used as a secured door position.

Profile Routine:

Press and hold the Profile Button for 5 seconds to initiate the “Install

Routine”. See Customizing the Settings on page 31.

NOTE: Refer to Step 34 for Wall Station programming instructions.

NOTE: The Wall Station arrows’ LED will light while any Wall Station

button remains pressed. See Maintenance section for battery

replacement.

Pet Button

Light Button

Up/Down Button

Timer Button

Profile Button

Slide Switch

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

OPERATION INSTALLATION

WARNING

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 45 46

Comments to this Manuals

No comments

Wayne-Dalton Optimal Owner's Manual Page 35

Comments to this Manuals

Related products and manuals for Garage Door Opener Wayne-Dalton Optimal