Wayne-dalton 9800 User Manual download pdf (Page 22)

Tools Needed:

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer.

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at www.wayne-dalton.com

Tools Needed:

Torsion End Bearing Brackets

End bearing brackets are right and left

hand. Break the end bearing brackets

apart.

Starting on the left hand side and using

the upper slots in the end bearing

bracket, position above the ﬂagangle

and secure the end bearing bracket to

the horizontal angle using (2) 3/8”-16

x 3/4” truss head bolts and (2) 3/8”-16

nuts.

IMPORTANT: END BEARING BRACKETS

MUST BE ATTACHED THROUGH THE

UPPER SLOTS ON 15” RADIUS TRACK.

Once the bracket is secured to the

horizontal angle, secure the top of the

end bearing bracket to the jamb using

(1) 5/16” x 1-5/8” lag screw. Repeat for

right hand side.

NOTE: Right and left hand is always

determined from inside the building

looking out.

Step Ladder

Power Drill

Ratchet Wrench

7/16” Socket

Driver

9/16” Socket

Driver

9/16” Wrench

LEFT HAND

END BEARING

BRACKET

UPPER SLOTS

USED ON 15”

RADIUS TRACK

(1) 5/16” X 1-5/8”

LAG SCREW

(2) 3/8”-16 X 3/4”

TRUSS HEAD BOLTS

(2) 3/8”-16 NUTS

Center Bearing Bracket

Power Drill

7/16” Socket

Driver

Level

Tape Measure

Pencil

1/4” Torx Bit

Measure to locate the center of the door

and mark a vertical pencil line on the

mounting surface above the door, to

indicate the center line of the door. Then,

measure from the center of the bearing, in

one of the end bearing brackets, DOWN to

the top of the door. Using that dimension,

measure UP from the top of the door

and mark a horizontal pencil line on the

mounting surface, intersecting the vertical

pencil line. Now align the edge of the center

bearing bracket along the vertical pencil

line on the mounting surface. Center the

bearing bracket on the horizontal line. This

will ensure the torsion tube is level between

the center and end bearing brackets. Attach

the center bearing bracket, in this location,

to the mounting surface, using

(2) 5/16” x 1-5/8” lag screws and (1) 5/16”

x 2” tamper-resistant lag screw.

IMPORTANT: USE THE 5/16” X 2” TAMPER-

RESISTANT LAG SCREW ONLY IF MOUNTING

SURFACE MOUNTED OVER MASONRY.

TAMPER-RESISTANT LAG SCREW MUST BE

ATTACHED THROUGH THE BOTTOM HOLE

OF THE CENTER BEARING BRACKET.

VERTICAL LINE

MOUNTING SURFACE

EQUAL DISTANCE

CENTER OF

END BEARING

BRACKET

HORIZONTAL LINE

CENTER BEARING

BRACKET

CENTER

BEARING

BRACKET

(1) 5/16” X 1-5/8” LAG SCREW

MOUNTING

SURFACE

HORIZONTAL LINE

VERTICAL

LINE

(1) 5/16” X 2”

TAMPER-RESISTANT LAG SCREW OR

(1) 5/16” X 1-5/8” LAG SCREW

HORIZONTAL

ANGLE

LEFT HAND

END BEARING

BRACKET

RIGHT HAND END

BEARING BRACKET

BREAK

THE END

BEARING

BRACKETS

APART

HORIZONTAL

ANGLE

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 33 34

Comments to this Manuals

No comments

Wayne-dalton 9800 User Manual Page 22

Comments to this Manuals

Related products and manuals for Furniture Wayne-dalton 9800